Arm Cortex R4F Uživatelský manuál Strana 175
- Strana / 456
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Events and Performance Monitor
ARM DDI 0363E Copyright © 2009 ARM Limited. All rights reserved. 6-11
ID013010 Non-Confidential, Unrestricted Access
Figure 6-4 FLAG Register format
Table 6-5 shows how the bit values correspond with the FLAG Register.
To access the FLAG Register, read or write CP15 with:
MRC p15, 0, <Rd>, c9, c12, 3 ; Read FLAG Register
MCR p15, 0, <Rd>, c9, c12, 3 ; Write FLAG Register
If an overflow flag is set to 1 in the FLAG register it remains set until one of the following
happens:
• writing 1 to the flag bit in the FLAG Register clears the flag
• the processor is reset.
The following operations do not clear the overflow flags:
• disabling the overflowed counter in the CNTENC Register
• disabling all counters in the PMNC Register
• resetting the overflowed counter using the PMNC Register.
6.3.5 c9, Software Increment Register
The Software INCRement (SWINCR) Register increments the count of a Performance Monitor
Count Register.
The SWINCR Register is:
• A write-only register that Reads-As-Zero
• Always accessible in Privileged mode. The USEREN Register determine accessibility in
User mode, see c9, User Enable Register on page 6-15.
Caution
You must only use the SWINCR Register to increment performance monitor count registers
when the counter event is set to
0x00
, software count, in the Event Select Register, see c9, Event
Selection Register on page 6-13.
C
31 3210
Reserved
P2
P1
P0
Performance monitor counters
overflow flags
Cycle count overflow
Table 6-5 Overflow Flag Status Register bit functions
Bits Field Function
[31] Cycle counter overflow Cycle counter overflow flag:
0 = disable
1 = enable.
[30:3] Reserved UNP on reads, SBZP on writes
[2] P2 Counter 2 overflow flag
[1] P1 Counter 1 overflow flag
[0] P0 Counter 0 overflow flag
- -R4 and Cortex-R4F 1
- Cortex-R4 and Cortex-R4F 2
- Contents 3
- Chapter 15 AC Characteristics 5
- Appendix B ECC Schemes 6
- Appendix C Revisions 6
- List of Tables 10
- List of Figures 13
- • Feedback on page xxi 16
- About this book 17
- Preface 18
- Feedback 21
- Chapter 1 22
- Introduction 22
- 1.1 About the processor 23
- 1.2 About the architecture 24
- AXI master bus 25
- AXI slave bus 25
- 1.5 Power management 33
- 1.6 Configurable options 34
- 0xFFFF0000 36
- 1.7 Execution pipeline stages 38
- 1.8 Redundant core comparison 40
- 1.9 Test features 41
- Chapter 2 47
- Programmer’s Model 47
- 2.2 Instruction set states 49
- 2.3 Operating modes 50
- 2.4 Data types 51
- 2.5 Memory formats 52
- 2.6 Registers 53
- Program status registers 55
- 2.7 Program status registers 56
- 2.8 Exceptions 62
- LDM ..,{..pc}^ 63
- SUBS PC, R14_irq, #4 64
- SUBS PC, R14_fiq, #4 65
- Register on page 4-35 67
- Imprecise abort masking 69
- Memory barriers 69
- Chapter 3 76
- 3.1 Initialization 77
- 3.2 Resets 81
- 3.3 Reset modes 82
- 3.4 Clocking 84
- Chapter 4 85
- VariantImplementor 98
- 31 23 20 19 16 15 4 3 0 98
- 29 28 19 18 16 15 3 2 0 100
- SReserved 101
- 31 16 8 7 1 0 101
- ReservedDRegion 101
- System Control Coprocessor 102
- Security extension 103
- ARMv4 Programmer’s model 103
- 31 12 11 8 7 4 3 0 103
- Reserved 103
- 0x00000000 105
- Reserved FCSE TCM PMSA VMSA 106
- Auxiliary Control Register 106
- Cache coherence 106
- Outer shareable 106
- Exclusive instructions 115
- Barrier instructions 115
- SMC instructions 115
- Reserved Level 119
- IRQ = 0x18 120
- 0x0000001C 121
- 0xFFFF0000-0xFFFF001C 121
- Bits Field Function 134
- [4:0] Reserved SBZ 134
- Reserved Region 137
- Figure 4-38 Cache operations 139
- Base address 142
- 31 12 11 7 6 2 1 0 142
- Reserved Size 142
- Privilege access 144
- AXI slave enable 144
- 31 16 15 78430 153
- [11:0] Reserved SBZ 156
- Chapter 5 160
- Prefetch Unit 160
- 5.1 About the prefetch unit 161
- 5.2 Branch prediction 162
- 5.3 Return stack 164
- Chapter 6 165
- 6.1 About the events 166
- 6.2 About the PMU 170
- 6.4 Event bus interface 183
- Chapter 7 184
- Memory Protection Unit 184
- 7.1 About the MPU 185
- Region 1 188
- Region 2 188
- Guard region 189
- 7.2 Memory types 190
- 7.3 Region attributes 192
- 7.5 MPU faults 195
- Chapter 8 197
- Level One Memory System 197
- 8.3 Fault handling 203
- 8.4 About the TCMs 209
- 8.5 About the caches 214
- Clean data cache by set/way 221
- 8.8 Error detection events 232
- Chapter 9 234
- Level Two Interface 234
- 9.1 About the L2 interface 235
- 9.2 AXI master interface 236
- LDMIA R10, {R0-R5} 250
- R10 = 0x1010 250
- 9.4 AXI slave interface 253
- 0x10000000 265
- Chapter 10 266
- Power Control 266
- 10.1 About power control 267
- 10.2 Power management 268
- Chapter 11 270
- 11.1 Debug systems 271
- 11.2 About the debug unit 272
- 11.3 Debug register interface 274
- DSAR CP14 c0, Debug Self 279
- Valid bits 281
- 31 12 11 2 1 0 281
- Bits Reset value Description 292
- Breakpoint value 292
- 0x00000007 293
- 0x0000000F 293
- 0x0000001F 293
- 0x7FFFFFFF 293
- 0xFFFFFFFC 294
- Lock implemented bit 298
- 11.5 Management registers 301
- Claim tag set 302
- 0xC5ACCE55 303
- Register number Function 305
- 11.6 Debug events 308
- 11.7 Debug exception 310
- — + 8 for ARM state 311
- 11.8 Debug state 313
- 11.9 Cache debug 319
- Example 11-15 Reading the PC 333
- Reading memory 334
- Chapter 12 342
- FPU Programmer’s Model 342
- Figure 12-1 FPU register bank 344
- 12.3 System registers 345
- Implementer Part number 346
- 31 24 23 22 16 15 8 7 4 3 0 346
- SVRM TE SPSR D DP 349
- Reserved I DNSP LS 350
- 12.4 Modes of operation 351
- 0xFF 0x7FF 352
- FCMPE(Z) 353
- Chapter 13 355
- Integration Test Registers 355
- Register (ITCTRL) 358
- Chapter 14 365
- • Dual issue on page 14-34 366
- Thumb instructions 369
- <Rn> 373
- 14.5 Media data-processing 374
- 14.7 Multiplies 376
- 14.8 Divide 378
- 14.9 Branches 379
- <addr_md_1cycle> 381
- <addr_md_3cycle> 381
- LDR R5, [R2, #4]! 382
- LDR R6, [R2, #0X10]! 383
- LDR R7, [R2, #0X20]! 383
- <addr_md_3cycle> 384
- RFEIA <Rn> 388
- SRSIA #<mode> 388
- MCR <cond> 390
- MRC <cond> 390
- 1- - - 392
- 14.23 Dual issue 398
- Chapter 15 401
- AC Characteristics 401
- 15.1 Processor timing 402
- Appendix A 414
- Processor Signal Descriptions 414
- A.2 Global signals 416
- A.3 Configuration signals 417
- A.5 L2 interface signals 421
- A.6 TCM interface signals 426
- A.8 Debug interface signals 430
- A.9 ETM interface signals 432
- A.10 Test signals 433
- A.11 MBIST signals 434
- A.12 Validation signals 435
- A.13 FPU signals 436
- Appendix B 437
- ECC Schemes 437
- Appendix C 439
- Revisions 439
- Glossary 442
- Write response channel (B) 444
- WT See Write-through 456
- Cache terminology diagram 456
Související produkty a manuály pro Hardware Arm Cortex R4F
Hardware Arm VERSION 1.2 Uživatelský manuál
(360 stránky)
(360 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce